Advertisement

A lot of data (in Italy) that was added before map 960 was lost probably due to the migration to the new map system (i reported the problem to tomtom months ago) and i hoped that this new map would have fixed those data migration problems. There is definitely something odd about this new 965 maps. Apparently i was wrong. Central and eastern europe tomtom download torrent files. This has never happened). For example the 'new' 965 Italy map is basically a copy and paste of the 960 (there are NO CHANGES AT ALL in a 10.000 km² area and in many big cities.

Summary of Contents for Lewmar V700

• Page 1 Lewmar V700 Vertical Windlass 65001022 Issue 5 Owner’s Installations, Operation & Servicing Manual..

• Page 2: Safety Notice

  • Boating, like many other activities can be hazardous. Even the correct selection, maintenance and use of proper equipment cannot eliminate the potential for danger, serious injury or death. • Lewmar windlasses are designed and supplied for anchor control in marine applications and are not to be used in conjunction with any other use.

• Page 3: Specifications

  3. Specifications 3.1 Gypsy Specifications Gypsies fitted to the V700 range of windlasses are ideally suited to handling our factory made Rope/Chain combination rodes, which consist of rope spliced to a chain tail. Ropes used must be windlass grade, medium lay nylon. Ropes from different manufacturers have wide variations in stretch and consistency in diameter.
• Page 4 196mm 73/4' 3.2 V700 Specifications NORMAL MOTOR MOTOR WORKING LOAD MAX. LINE TYPICAL LINE CIRCUIT MAX. PULL CURRENT WEIGHT SUPPLY POWER LIMIT SPEED SPEED BREAKER DRAW Voltage Watt m/min ft/min m/min ft/min 3.3 Dimensions Diagram 196mm 73/4' 4. Installation 4.1 Basic requirements..
• Page 5 4.2 Accessories Use only genuine Lewmar parts and accessories to ensure top performance and eliminate the risk of voiding your warranty. For replacement parts, please see §9 or visit your dealer or www.lewmar.com 4.3 Fitting the windlass to the deck 1.
• Page 6 4.3-5 4.3-6 5. Fully screw the three mounting studs into the base of the windlass. This can be done, quite simply, using the multi-tool wrench supplied. Screw the studs into the base finger tight, with the flats towards the base as shown (Fig 4.3-5).

• Page 7: Electrical Wiring

  5. Electrical wiring 5.1 Electric cable selection Lewmar recommends the installer source and install cable that meets the requirements of the standards and regulations relevant to the installation and codes of practice. The cable table gives recommended cable sizes based on total length of cable required, from the battery, following the route of the cables.
• Page 8 5.4 V700 Wiring diagram (toggle switch) Choice of cable thickness depends on total cable length: A + B + C + D + E = Battery to windlass, windlass to battery.
• Page 9 5.5 V700 Wiring diagram (contactor) Lewmar V700 Vertical Winlass ref 65001022 iss.5..
• Page 10 6. Operation 6.1 Operating tips Vessels at anchor will snub on the rode and this can cause slippage or apply excessive loads to the windlass. 1. When anchoring, power rode out allowing the vessel to take up stern away preventing the rode tangling with anchor.
• Page 11 If it is safe to do so, let go under power by operating a ‘Down’ control. Release the control when sufficient rode has been paid out. 6.5 Lying to anchor safely Vessels at anchor will snub on the rode and this can cause slippage or apply excessive loads to the windlass. Lewmar V700 Vertical Winlass ref 65001022 iss.5..
• Page 12 6.6 Hauling in Untie the bridle or replace the rode in the gypsy. If it is safe to do so, operate an ‘Up’ control. The fallsafe pawl (32) does not need to be disengaged during retrieval as it will act as a ratchet. When the anchor has been retrieved and is stowed in the bow roller, the fallsafe pawl should be left engaged in the gypsy to prevent accidental deployment of the anchor whilst underway.
• Page 13 • Turn the fall safe lever (34) so it is horizontal. • Remove fall safe shoulder screw (35) using allen wrench. • Lift off fall safe pawl (32). Remove fall safe spring (36). Lewmar V700 Vertical Winlass ref 65001022 iss.5..

• Page 14: Trouble Shooting

  • Replace new part by reversing the above procedure. 7.6 Fall safe lever replacement • Turn fall safe lever (34) so it is horizontal. • Remove socket screw (6) using allen wrench. • Remove fall safe lever (34). • To refi t use thread lock on the socket screw (6). •..
• Page 15 9- Part list Lewmar V700 Vertical Winlass ref 65001022 iss.5..
• Page 16 9.1 Service kits KIT NO. KIT DESCRIPTION ITEMS INCLUDED (QTY.) 66000099 Clutch Lever Clutch Lever (1) 66000600 Control Arm Kit 12(1), 24(1), 30(1) 66000601 Gypsy Cap Kit 21(1), 31(1) 66000602 Mounting Kit 5/16” USA 18(1), 26a(1), 33(1), 38(1) 66000603 Gypsy RC 1/4”G4 & 7mm Kit 37a(1), 40(1) 66000604 Gypsy RC 6 mm DIN 766 Kit..
• Page 17 Lewmar grants no other warranties regarding the fitness iii Lewmar shall not be liable in any way for Product failure, for purpose, use, nature or satisfactory quality of the or any resulting loss or damage that arises from: products.
• Page 18 Notes:..
• Page 19 Notes: Lewmar V700 Vertical Winlass ref 65001022 iss.5..
• Page 20 Fax: +44 (0)23 9248 5720 Email: info@lewmar.com Lewmar 351 New Whitfield Street Guilford, CT 06437 Tel: +1 203 458 6200 Fax: +1 203 453 5669 Email: info@lewmarusa.com www.lewmar.com Part No 65001022 Iss.5 © Copyright 2016 Lewmar Ltd. All rights reserved.