Psa Xs Evolution Driver
Posted admin
Psa Xs Evolution Driver Rating: 5,0/5 7053 reviews
Please make sure you read Rules! and DO NOT upload/post any illegal softwares or Pirated Material , Thank you for understanding :)
All Repairs PSA XS EVOLUTION interface !
Post: #1 |
| All Repairs PSA XS EVOLUTION interface ! Hi, Here is face down (LED side) of five microprocessor electronics boards of XS EVOLUTION interfaces. Two of them, in this case the two electronic boards to the left in the photo above, have communication problems on CAN bus, and particularly on FULL CAN vehicles. These two cards out: The three others, here, do not have this concern: When you look carefully at the two cards down, one perceives a missing component here: This is a 10Kohms resistor (marking 103); PULL UP resistor placed on the CAN line that comes the PIN P94 / TXO microprocessor MB90F546GS and then passes through the logic of HA08 before reaching the optocoupler HCPL 063N! So if you have CAN communication problems with your interfaces, you can already take a look to see if this resistance is present! Pending your back ... Regards. |
| Reputation: +7 - McMihai [+1] , carpi [+1] , HeXeN [+1] , mista [+1] , muko_82 [+1] , barto39 [+1] , galaxia [+1] |
The following 29 users say Thank You to titoun for this post:29 users say Thank You to titoun for this post • 530d, ALC1, autoaziz, barto39, bekiyu, benguessoum, bolecurug, bouizanne, BS68, carpi, diagdata, Dinho, djslowrnb, ETPerformance, fluorescent, gabivw, galaxia, HeXeN, kiko80, loki954, marianro2007, maxime47, McMihai, Michael1, Mind-Twist, mista, muko_82, Renopower, robalo |
04-02-2018, 04:24 AM, (This post was last modified: 04-02-2018, 13:09 PM by Michael1.) |
| All Repairs PSA XS EVOLUTION interface ! Hi Please help I have problem with Lexia interface, normallly it worked, during the reinstallation of DiagBox installed driver OK Led light normal but after that the interfacve is dead, I tried repleace USB cable, nothing, open iterface an measure conecting, cable and VGA conecor are good, interface have +5 V and grund through USB, D+ and D- from USB passing through small chip?? maybe that this is prblem ? here is 6 pin, there is small resistance (cca 20 ohm) measured betwen pin 1 - 6 and 3 -4 , that is maybe OK if it is noise filter? but i am not sure. Thanks in advance Best Regards Michael |
• |
Post: #3 |
| RE: All Repairs PSA XS EVOLUTION interface ! Hi, ESD suppressors : ref USBUF01W6 Marking code UU1 B.regards |
| Reputation: +1 - carpi [+1] |
The following 1 user says Thank You to titoun for this post:1 user says Thank You to titoun for this post • carpi |
Post: #4 |
| RE: All Repairs PSA XS EVOLUTION interface ! Hi When I connect the interfacco to the USB laptop does not see it, LED notlight, have you any idea where is problem? Thanks in advance best regards Michael |
• |
Post: #5 |
| RE: All Repairs PSA XS EVOLUTION interface ! Maybe microprocessor MB90F546GS is bricked... ? try an hardware reflash of this! B.regards |
| Reputation: +1 - carpi [+1] |
The following 1 user says Thank You to titoun for this post:1 user says Thank You to titoun for this post • carpi |
Post: #6 |
| RE: All Repairs PSA XS EVOLUTION interface ! Good Morning, I have just been updating the firmware with Scary interface tool, during update cable got unplugged, and now the unit fails to respond. Green light is on but Scary's interface checker does not show anything. Is it possible to re-flash using another way? any help appreciated. Thank you. Best regards Andy |
• |
Post: #7 |
| RE: All Repairs PSA XS EVOLUTION interface ! I have same problem, how can i do hardware reflash? (18-02-2018, 16:48 PM)Michael1 Wrote: Hi |
• |
| Possibly Related Threads... | |||||
| Thread | Author | Replies | Views | Last Post | |
| Lexia interface recognization problem | Jedrek | 0 | 159 | 01-04-2019, 20:26 PM Last Post: Jedrek | |
| Precautions for original Peugeot Planet Interface | allpro | 6 | 484 | 01-03-2019, 14:00 PM Last Post: leon163 | |
| Interface not recognized... :-( | cro1983 | 17 | 1,117 | 19-02-2019, 22:02 PM Last Post: Batru | |
| Reflash lexia interface from C to B | guerragt5 | 7 | 647 | 03-02-2019, 15:30 PM Last Post: mattydr67 | |
| [NEED] PSA Interface Checker v4.0 | roanoke | 2 | 3,931 | 17-01-2019, 15:11 PM Last Post: rezayeto | |
| Solved ✔The interface is recognized in usb but the green light turn off and does not work. | Rafiusk | 17 | 1,562 | 11-01-2019, 17:42 PM Last Post: mattydr67 | |
| Edit your XS EVOLUTION interface to make it equivalent to an original! | titoun | 10 | 8,285 | 08-01-2019, 09:04 AM Last Post: Multipla2009 | |
| PSA interface FIRMWARE 4.3.7 from official diagbox 9.37 | 911sniper | 0 | 2,118 | 21-11-2018, 14:55 PM Last Post: 911sniper | |
| actia psa xs evolution 9780-z5 serial number banned | Stony2018 | 2 | 576 | 29-09-2018, 15:53 PM Last Post: Stony2018 | |
| Reflash lexia interface from B to C | lionofthedesert | 58 | 30,754 | 25-09-2018, 10:38 AM Last Post: Helder Lopes | |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to ContentGarageForum›GarageForum - Cars Forums›Automotive Software›General - Others
| Latest news: |
i have, actia psa xs evolution ¿drivers and software?
Thread Rating:
- 0 Votes - 0 Average
i have, actia psa xs evolution ¿drivers and software? |
Post: #1 |
| i have, actia psa xs evolution ¿drivers and software? hello tradis, proud to be a member of GarageForum since Mar 2016.hi have actia odb 9780.z5 I need to work on 64-bit windows 7 where I can get better mega drivers and software |
03-09-2016, 04:41 PM |
RE: i have, actia psa xs evolution ¿drivers and software? (03-08-2016 09:46 AM)tradis Wrote: helloHi, Is not possible to work any vci on X64 versions of Windows YomGui |
User(s) browsing this thread: 1 Guest(s)